e-mail address: omnetmanual@gmail.com

Phone number: +91 9444856435
DEFENDER

Switching protocols Project examples using omnet++

Switching Protocols using OMNeT++tool ideas are discussed by us. Get fresh and original ideas from us, we are ready at your service to provide you with best thesis topics and simulation results. Network comparison are also provided by us. The below are some project ideas that concentrate on switching protocols using OMNeT++:

  1. Simulating Basic Ethernet Switching
  • Objective: Execute and simulate simple Ethernet switching within a network.
  • Details:
    • Configure a network topology with multiple switches and end devices.
    • Execute Ethernet switching, in which switches learn the MAC addresses of connected devices and forward frames based on MAC address tables.
    • To emulate the traffic flow within the network and measure the performance in terms of latency, throughput, and packet delivery ratio.
  1. Virtual LAN (VLAN) Switching
  • Objective: Execute and emulate VLAN switching in a network to isolate the traffic into diverse virtual networks.
  • Details:
    • Generate a network topology with multiple VLANs configured via numerous several switches.
    • Execute VLAN tagging and switching, make sure traffic is properly segregated and routed.
    • Mimic inter-VLAN routing using a Layer 3 switch or router and measure the performance in terms of traffic isolation, bandwidth utilization, and security.
  1. Simulation of Spanning Tree Protocol (STP)
  • Objective: Execute STP in a network to mitigate loops and make sure a loop-free topology.
  • Details:
    • Configure a network topology with redundant paths and multiple switches.
    • Execute STP to disable redundant paths and supports a single active path to each network segment.
    • Measure the network’s convergence time, fault tolerance, and the effectiveness of the spanning tree.
  1. Quality of Service (QoS) in Switches
  • Objective: Execute QoS mechanisms in switches to select the traffic based on different criteria like type of service.
  • Details:
    • To mimic a network with multiple switches that manages the numerous kinds of traffic that has voice, video, and data.
    • Execute QoS policies in switches, like traffic shaping, policing, and priority queuing.
    • Measure the effects of QoS on network performance that has performance metrics like jitter, latency, and throughput for different traffic classes.
  1. Simulating a Layer 3 Switch
  • Objective: Execute and emulate a Layer 3 switch that performs both switching and routing within a network.
  • Details:
    • Make a network topology with a Layer 3 switch that can forward packets based on both MAC and IP addresses.
    • Executing routing protocols like OSPF or RIP within the Layer 3 switch to handles the inter-network traffic.
    • To emulate the diverse network scenarios and measure the performance of Layer 3 switching in terms of routing efficiency, traffic management, and scalability.
  1. Multiprotocol Label Switching (MPLS) in a Switched Network
  • Objective: Execute MPLS within a switched network to enhance the traffic engineering and optimize the network performance.
  • Details:
    • Configure a network with MPLS-enabled switches that can forward packets based on labels rather than IP addresses.
    • Execute label distribution protocols and create label-switched paths (LSPs) via the network.
    • To mimic numerous traffic scenarios and measure how MPLS enhances the traffic management, decrease the latency, and improves the network throughput.
  1. Data Center Network Simulation with Software-Defined Networking (SDN) Switches
  • Objective: Execute SDN-based switching in a data centre network to permits the dynamic network management.
  • Details:
    • Generate a data centre topology with multiple SDN-enabled switches.
    • Execute an SDN controller that enthusiastically handles the switching decisions based on real-time network conditions.
    • Measure the performance of the SDN-based switching architecture in terms of resilience, efficiency, and responsiveness to varying traffic patterns.
  1. Switching in Wireless Mesh Networks
  • Objective: Execute and emulate the switching protocols in a wireless mesh network in which the nodes act as both hosts and switches.
  • Details:
    • Model a wireless mesh network topology in which the each node can switch packets among its neighbours.
    • Executes a switching protocol to handles the traffic flow within the mesh network.
    • Measure the performance of the mesh network in terms of route stability, network coverage, and overall throughput.

Finally, here we get knowledge of some of the examples for switching protocols that performs in OMNeT++ simulation tool.  Also we deliver the further elaborated detail regarding the switching protocols.

Related Topics